Miele TKB 440 WP Operating Instructions Manual Download Page 24

Page: 24 / 72

3. Select a programme and start it

Select any options or delay

start (if required)

Please see "Options" for further infor‐

mation.

To select options



Press a button.

The button will light up when the option

is selected.

Delay start

You can delay the start of the pro‐

gramme.

However:

delay start cannot be used

with the

Warm air

programme.



Touch the



sensor.

–



will flash

Please see "Delay start" for more in‐

formation.

Start the programme



Press the flashing

Start/Stop

button.

The

Start/Stop

button will now light up

constantly.
The

Perfect Dry

indicator will only flash/

light up with programmes with selecta‐

ble drying levels (see also "Operating

the tumble dryer").
The laundry will be cooled down shortly

before the end of the programme.

Summary of Contents for TKB 440 WP









































































Search results

Summary of Contents for TKB 440 WP

Reviews:

Related manuals for TKB 440 WP

Brands by name

Popular brands

Miele TKB 440 WP, Operating Instructions Manual

Search results

Summary of Contents for TKB 440 WP

Reviews:

Related manuals for TKB 440 WP

Brands by name

Popular brands