Miele TCE 620 WP Operating Instructions Manual Download Page 49

Page: 49 / 76

What to do if ...

Problem

Cause and remedy



lights up

The programme selector has been moved.



Select the original programme. The time remaining
will appear in the display again.

Bars flash in the display
at the end of a
programme:



...



...



...

The programme has finished but the laundry has not
yet cooled down.



Either remove the laundry and spread it out to cool
down or leave it in the tumble dryer to cool down
during the cooling phase.



flashes/lights up

after the tumble dryer
has been switched on
and a programme
cannot be selected

Access via a code has been activated.



See "Programmable functions -



Code".



and



light up after

a programme has been
cancelled, a signal
sounds

An excessive amount of fluff has built up.



Clean the fluff filters.



Clean the plinth filter.



Clean the airways: the area underneath the plinth
filter and the heat exchanger.



See "Cleaning and care".

To switch

 

off:



Switch the dryer off and then on again.

You can influence this error message yourself: see
"Programmable functions" and the part on the "



Airways indicator".



and another number

combination flash after
a programme has been
cancelled, a signal
sounds

No obvious cause.



Switch the dryer off and then on again.



Start a programme.

If the programme is cancelled again and an error
message appears, there is a fault. Contact the Miele
Service Department.





lights up and the

programme has been
cancelled, a signal
sounds

The laundry is unevenly distributed or has rolled up.



Disentangle the laundry and remove a few items, if
necessary.



Switch the dryer off and then on again.



Start a programme.

Summary of Contents for TCE 620 WP













































































Search results

Summary of Contents for TCE 620 WP

Reviews:

Related manuals for TCE 620 WP

Brands by name

Popular brands

Miele TCE 620 WP, Operating Instructions Manual

Search results

Summary of Contents for TCE 620 WP

Reviews:

Related manuals for TCE 620 WP

Brands by name

Popular brands