Miele TCE 620 WP Operating Instructions Manual Download Page 26

Page: 26 / 76

3. Select a programme and start it

Programme selection

The dryer is switched on when you
select a programme, and switched off
by turning the programme selector to
the



position.



Turn the programme selector.

A drying level can also light up and
durations will appear in the time display.

Programmes with drying levels

–

Cottons, Minimum iron, Delicates,
Express, Shirts, Denim, Outerwear,
Pre-ironing

The drying level can be altered after
selecting one of these programmes.



Touch the sensor for the drying level
you want, it then lights up brightly.

Any drying level can be selected for the

Cottons

and

Express

programmes. A

more limited range is available when
using the other programmes.

Summary of Contents for TCE 620 WP













































































Search results

Summary of Contents for TCE 620 WP

Reviews:

Related manuals for TCE 620 WP

Brands by name

Popular brands

Miele TCE 620 WP, Operating Instructions Manual

Search results

Summary of Contents for TCE 620 WP

Reviews:

Related manuals for TCE 620 WP

Brands by name

Popular brands