Miele T 8861 WP Edition 111 Operating Instructions Manual Download Page 58

Page: 58 / 64

Setting Standby

To save energy, the display goes out
after 10 minutes and the indicator
light for the

Start/Stop

button will start

flashing slowly.

Reactivating from Standby

Turning the programme selector or
pressing one of the buttons switches
the display back on again. This will
not alter a running programme.

Standby is activated:

– if a programme is not selected after

the machine has been switched on.

– after a programme has started.

However: The display will switch on for
10 minutes if Delay start has finished,
after the end of a progamme or the
Anti-crease cycle.
The buzzer (if selected) will sound for
10 minutes after the end of a
progamme.

Factory default; Not in current
programme

As described under "On".
But: The display and indicator lights will
not switch off during a programme.

Off

The display and indicator lights will not
switch off when the dryer is switched
on.

Follow steps (

...) to

programme and store in memory.

See the next page.

Programmable functions

Summary of Contents for T 8861 WP Edition 111

































































Search results

Summary of Contents for T 8861 WP Edition 111

Reviews:

Related manuals for T 8861 WP Edition 111

Brands by name

Popular brands

Miele T 8861 WP Edition 111, Operating Instructions Manual

Search results

Summary of Contents for T 8861 WP Edition 111

Reviews:

Related manuals for T 8861 WP Edition 111

Brands by name

Popular brands