Miele T 8861 WP Edition 111 Operating Instructions Manual Download Page 56

Page: 56 / 64

Altering the volume of the
buzzer

The buzzer has two volumes.

Follow steps (

...) to

programme and store in memory.

Before you begin, first ensure that:

– The dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Switch the dryer on.

Wait until the indicator light for the

Start/Stop

button lights up constantly. . .

. . . and then release the

Start/Stop

button.

Press the

Gentle tumble

button three

times.

– The

Gentle tumble

indicator light will

briefly flash four times.

The option selected will be displayed
by a

number

which will alternate with

Factory default setting; Normal
buzzer

Loud buzzer

(The

Automatic plus

indicator light

will also flash)

Pressing the

Start/Stop

button

switches from one number to the
other.

Switch the dryer off.

The setting you have selected is now
stored in memory. You can alter the
settings again at any time.

Check

Repeat steps

Switch the dryer off after step

Programmable functions

Summary of Contents for T 8861 WP Edition 111

































































Search results

Summary of Contents for T 8861 WP Edition 111

Reviews:

Related manuals for T 8861 WP Edition 111

Brands by name

Popular brands

Miele T 8861 WP Edition 111, Operating Instructions Manual

Search results

Summary of Contents for T 8861 WP Edition 111

Reviews:

Related manuals for T 8861 WP Edition 111

Brands by name

Popular brands