Miele T 8685 C Operating Instructions Manual Download Page 56 | Manualshive

Page: 56 / 68

background image

Drying levels

You can alter the drying levels for the

Cottons

and

Minimum

iron

programmes.

The bar chart shows you the setting.
Factory default: a medium setting.

Depending on the setting, the programme duration will be
shorter (Damper) or longer (Drier).

Extended cool down

The cooling down phase which takes place before the end
of a programme can be lengthened if required. This makes
the garments easier to handle.

The bar chart shows you the setting.
Factory default: 0 mins (normal cooling down period)

You can select an extended cool down time in 2 minute
increments up to a maximum of 18 minutes.

You cannot extend the cooling down time for the Warm air,
Cool air, Timed drying hygiene, Woollens handcare, Silks
handcare or Smoothing programmes.

Settings menu

J

56

«
...
54
55
56
57
58
...
»

Summary of Contents for T 8685 C





































































Reviews:

No comments

Related manuals for T 8685 C

Brand: PALSON Pages: 11

Brand: inventum Pages: 24

Brand: OMEGA AIR Pages: 34

Brand: Gastro Pages: 13

Brand: OdorStop Pages: 2

Brand: tomado Pages: 68

Brand: Boekel Pages: 2

Brand: Cobra Pages: 20

Brand: Cobra Pages: 38

Brand: TriStar Pages: 40

Gold GGQ9800PW3

Brand: Whirlpool Pages: 20

Gold GGW9868KL5

Brand: Whirlpool Pages: 28

EasyDry Wide-Corr Centurion 24 Series

Brand: Westeel Pages: 214

Brand: Franke Pages: 20

Brand: FRAM Pages: 46

Brand: Somogyi Pages: 37

Brand: Morgan Pages: 6

Brand: Bobrick Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands