Miele T 8164 WP Operating Instructions Manual Download Page 45

Page: 45 / 56

Settings

Altering the residual moisture

level in the Cottons

programme

The tumble dryer is designed to dry

effectively using as little energy as

possible. However, if you require the

laundry to be drier or damper, you can

reduce or increase the default residual

moisture in this programme.

Exception:

Normal

remains unchanged.

Follow steps (







...) to

programme and store in memory.
Before you begin, ensure that:

– The tumble dryer is switched off.
– The door is closed.
– The programme selector is pointing

Finish



Press

Start

and keep it pressed in

whilst carrying out steps







Switch the dryer on.



Wait until the indicator light for the

Start

button comes on . . .



. . . and then release the

Start

button.

The

Empty container

indicator light will

flash once.

The option selected will be displayed

by a

number

which will alternate with





Laundry will be damper



The

standard drying level will

remain on the Normal setting

(factory default setting)

(The

Clean out airways

indicator light

will also flash once)



Laundry will be drier

(The

Clean out airways

indicator light

will also flash twice)



Pressing the

Start

button switches

between the options.



Switch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:



Carry out steps







Switch the dryer off after checking.

Summary of Contents for T 8164 WP

























































Search results

Summary of Contents for T 8164 WP

Reviews:

Related manuals for T 8164 WP

Brands by name

Popular brands

Miele T 8164 WP, Operating Instructions Manual

Search results

Summary of Contents for T 8164 WP

Reviews:

Related manuals for T 8164 WP

Brands by name

Popular brands