Miele T 8164 WP Operating Instructions Manual Download Page 49

Page: 49 / 56

Settings

Altering the standard drying

level in the"Automatic plus"

programme

The drying level for this programme is

set at a standard

Normal

level. You

have the option of changing to

Hand

iron

(damper than Normal) or to

(drier than Normal).

Follow steps (







...) to

programme and store in memory.
Before you begin, ensure that:

– The tumble dryer is switched off.
– The door is closed.
– The programme selector is pointing

Finish



Press

Start

and keep it pressed in

whilst carrying out steps







Switch the dryer on.



Wait until the indicator light for the

Start

button comes on . . .



. . . and then release the

Start

button.



Turn the programme selector to

Cottons Hand iron

The

Empty container

indicator light will

flash six times.

The option selected will be displayed

by a

number

which will alternate with





Standard setting -

Hand iron



The

standard drying level will

remain on the Normal setting

(factory default setting)

(The

Clean out airways

indicator light

will also flash once)



Standard setting will be

(The

Clean out airways

indicator light

will also flash twice)



Pressing the

Start

button switches

between the options.



Switch the dryer off.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check the setting:



Carry out steps







Switch the dryer off after checking.

Summary of Contents for T 8164 WP

























































Search results

Summary of Contents for T 8164 WP

Reviews:

Related manuals for T 8164 WP

Brands by name

Popular brands

Miele T 8164 WP, Operating Instructions Manual

Search results

Summary of Contents for T 8164 WP

Reviews:

Related manuals for T 8164 WP

Brands by name

Popular brands