Miele SUPERTRONIC Operating Instructions Manual Download Page 61

Page: 61 / 94

The following fault message appears in the display and the
programme has been cancelled.

Fault message

Possible cause

Remedy

Water inlet

fault

The water inlet is
blocked or
restricted.

Check whether

– the tap has been turned on

properly.

– the inlet hose is kinked.

– the water pressure is too low.

Drain fault

– The water outlet is

blocked or
restricted.

– The drain hose

has been fixed
too high.

– Clean the drain filter and

drain pump.

– The maximum drain height is

1m.

Waterproof

system has

reacted

The water protection
system has reacted.

– Turn off the tap.

– Call Miele.

;

Technical fault

F xxx

There is a fault.

Start the programme again.
If the fault message appears
again, contact Miele.

To switch off the fault message: Switch the machine off with the

button.

Problem solving guide

Summary of Contents for SUPERTRONIC































































































Search results

Summary of Contents for SUPERTRONIC

Reviews:

Related manuals for SUPERTRONIC

Brands by name

Popular brands

Miele SUPERTRONIC, Operating Instructions Manual

Search results

Summary of Contents for SUPERTRONIC

Reviews:

Related manuals for SUPERTRONIC

Brands by name

Popular brands