manualshive.com logo in svg

Miele PT 5136 OS, Operating And Installation Instructions

Share
Download
Miele PT 5136 OS Operating And Installation Instructions Download Page 53

Calculation example

A

Wall pipe, with louvred vent

= 1 x 3.8 m Additional duct
length

= 3.8 m

B/D

2 bends, 90°

= 2 x 0.8 m Additional duct
length

= 1.6 m

C

0.5 m plastic piping

= 0.5 x 1 m Additional duct
length

= 0.5 m

E

Side connection, left

= 1 m Additional duct length

= 1.0 m

total duct length

= 6.9 m

Result: A duct diameter of 100 mm is
adequate as the total duct length is less
than the 20 m specified in Table II.

Installation to the rear, left or
right hand side of the machine

To the rear

The connection is opened at the
factory.

^

Fit one of the venting systems
described on the following pages.

To the left or right side of the
machine.

^

Turn the cover flap anti-clockwise.

^

Refit it securely in the rear outlet.

^

Fit one of the venting systems
described on the following pages.

Installation - extraction ducting

53

Summary of Contents for PT 5136 OS





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands