manualshive.com logo in svg

Miele PG 8591, Operating Instructions Manual

Share
Download
Miele PG 8591 Operating Instructions Manual Download Page 128

Problem solving guide

128

Problem

Cause and remedy

The load is flecked.

The rinsing agent container is empty.

Refill the container.

The rinsing agent concentration is set too low.

Contact the Miele Customer Service Department and
have the dispensing concentration reset.

The cleaning result is un-
satisfactory.

Mobile units, baskets, modules and inserts were not
suitable for the load.

Select mobile units, baskets, modules and inserts which
are suitable for the task.

Mobile units, baskets, inserts and modules were incorrectly
loaded or overloaded.

Arrange the wash load correctly according to the
information in the Operating instructions.

Avoid overloading the mobile units, baskets, modules
and inserts.

The programme was not suitable for the soiling.

Select a suitable programme.

or

Adjust the parameters to suit the task.

Soiling has been left to dry on the wash load for too long.

Soiling should not be left on the load for more than 6
hours before machine reprocessing.

A spray arm is blocked.

Ensure the spray arms are not obstructed when
arranging the wash load.

Injector nozzles on the mobile units, baskets, modules or
inserts are blocked.

Check the nozzles and clean them as necessary.

The filters in the wash cabinet are dirty.

Check the filters and clean them if necessary.

Mobile units, baskets or modules were not correctly
mounted on the water connection.

Check the adapter.

Summary of Contents for PG 8591

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands