Miele PG 8083 SCVi Operating Instructions Manual Download Page 65

Page: 65 / 84

General problems with the dishwasher

Problem

Possible fault

Solution

The indicator lights
and the display are
dark. Only the
indicator light

flashes slowly.

The indicators and the
display turn off
automatically to save
energy (Standby).

Press the

button to come

out of Standby mode.

The interior lighting
does not come on
when the door is
opened.

The interior lighting was
permanently turned off.

Turn the interior lighting back
on (see "Additional options -
BrilliantLight").

The following fault
message is
displayed:

Salt reservoir cover

The buzzer sounds
and the optical
interface flashes
during the program
sequence.

The salt reservoir cover
is not properly closed.

– Close the salt reservoir

cover.

If the salt reservoir cover
opened during a program:

– Push the

button to turn

the dishwasher off (even if it
appears to be off) and on
again.

– Re-start the program.

The buzzer sounds
during the program.
The following fault
message is
displayed:

Spray arm blocked

The middle spray arm is
blocked by dishware.

Open the dishwasher door
and rearrange items blocking
the spray arms.

The spray arm jets of the
middle arm are clogged.

– Press the

button to turn

the dishwasher off.

Then:

– Clean the spray arm (see

"Cleaning and care").

Frequently asked questions

Summary of Contents for PG 8083 SCVi





















































































Search results

Summary of Contents for PG 8083 SCVi

Reviews:

Related manuals for PG 8083 SCVi

Brands by name

Popular brands

Miele PG 8083 SCVi, Operating Instructions Manual

Search results

Summary of Contents for PG 8083 SCVi

Reviews:

Related manuals for PG 8083 SCVi

Brands by name

Popular brands