Miele PG 8083 SCVi Operating Instructions Manual Download Page 61

Page: 61 / 84

Repairs should only be carried out by a qualified and trained person in

accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.

Technical faults

Problem

Possible fault

Solution

The dishwasher does
not start.

The door is not properly
closed.

Push the door firmly closed.

The dishwasher is not
plugged in.

Insert the plug.

The circuit breaker has
tripped.

– Reset the circuit breaker.

See the data plate for
minimum amperage.

– If the circuit breaker trips

again. Contact Miele.

The dishwasher is not
turned on.

Press the

button and

select a program.

The dishwasher stops
during a program.

The circuit breaker has
tripped.

– Reset the circuit breaker

(see data plate for the
correct fuse rating).

– If the circuit breaker trips

again, contact Miele.

The optical interface
does not light up after
program start.

The light guide was not
installed correctly.

Install the light guide
correctly (see the installation
diagram).

Frequently asked questions

Summary of Contents for PG 8083 SCVi





















































































Search results

Summary of Contents for PG 8083 SCVi

Reviews:

Related manuals for PG 8083 SCVi

Brands by name

Popular brands

Miele PG 8083 SCVi, Operating Instructions Manual

Search results

Summary of Contents for PG 8083 SCVi

Reviews:

Related manuals for PG 8083 SCVi

Brands by name

Popular brands