Miele PG 8080 U Operating Instructions Manual Download Page 32 | Manualshive

Page: 32 / 84

background image

Adjusting the upper basket

In order to gain more space for taller
items in the lower or upper basket, the
upper basket can be adjusted to three
levels of about 2 cm height difference
between each level.

The upper basket can also be set at an
angle with one side high and the other
side low to improve water drainage.
However, make sure that the basket
can slide smoothly in and out of the
cabinet.

^

Pull the upper basket out.

To adjust the upper basket upwards:

^

Lift the basket up until it clicks into
place.

To adjust the upper basket downwards:

^

Pull upwards on the levers at the
sides the basket.

^

Adjust the basket to the desired
height and then push the levers
securely back down into position.

Depending on the setting of the upper
basket, the following plate dimensions
can be accommodated.

Dishwasher with cutlery basket

Upper

basket

level

Plate

C

in cm

Upper

basket

Lower

basket

Top

20

31

Middle

22

29

Bottom

24

27

Loading the commercial dishwasher

32

«
...
30
31
32
33
34
...
»

Summary of Contents for PG 8080 U





















































































Reviews:

No comments

Related manuals for PG 8080 U

Brand: Haier Pages: 38

Brand: Candy Pages: 136

Brand: Candy Pages: 41

Brand: VOX electronics Pages: 154

Brand: Merax Pages: 22

Brand: Amica Pages: 2

Brand: Silverline Pages: 88

Brand: Asko Pages: 2

Brand: WESCO NAVY Pages: 186

Brand: Hotpoint Pages: 16

Brand: EuropAce Pages: 18

Brand: Haier Pages: 52

Brand: Haier Pages: 45

WF8804FS(A/F/G/H/S/V/W/Z)

Brand: Samsung Pages: 72

Brand: Samsung Pages: 40

Brand: Electrolux Pages: 26

Brand: Electrolux Pages: 35

Brand: Electrolux Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands