Miele PDR 507 HP Operating And Installation Instructions Download Page 48

Page: 48 / 92

Fragrance flacon

Removing/replacing the
fragrance flacon



Turn the outer ring anti-clockwise
until markers

and

line up.



Replace the fragrance flacon with a
new one.

When not in use, you can store the
fragrance flacon in its original
packaging.

Fragrance flacons are available to
order from Miele or via the Miele
online shop.

Fragrance can leak. Do not lay the
fragrance flacon down.

– If you are keeping the fragrance

flacon in its original packaging, do
not store the packaging upright on its
edge or upside down. Otherwise, the
fragrance will leak out.

– Always store in a cool, dry place

away from direct sunlight.

– When purchasing new fragrance

flacons, only remove the protective
seal just before use.

Summary of Contents for PDR 507 HP





























































































Search results

Summary of Contents for PDR 507 HP

Reviews:

Related manuals for PDR 507 HP

Brands by name

Popular brands

Miele PDR 507 HP, Operating And Installation Instructions

Search results

Summary of Contents for PDR 507 HP

Reviews:

Related manuals for PDR 507 HP

Brands by name

Popular brands