Miele Optima G 1470 Operating Instructions Manual Download Page 48 | Manualshive

Page: 48 / 68

background image

With the aid of the following guide, minor problems can be easily corrected
without calling in a Miele service technician, saving you both time and money.

The following guide may help you to find the reason for a fault, and to correct it.
You should, however, note the following:

,

Repairs should only be carried out by a suitably qualified and trained

person in accordance with current local and national safety regulations.
Unauthorised or incorrect repairs could cause personal injury or damage the
appliance.

Technical problems

Problem

Possible cause

Remedy

The appliance does
not start.

The door is not properly
closed.

Push the door firmly shut.

The appliance is not
plugged in.

Insert the plug and switch on
at the socket.

The fuse is defective or
has tripped.

Reset or replace the fuse.

The appliance is not
switched on.

Press the On button

g

and

select a programme.

The dishwasher
stops during a
programme.

The fuse is defective or
has tripped.

Reset or replace the fuse.

After the programme
has started, the
In-operation indicator
light is not visible.

The reflector panel was
not correctly fitted.

Re-fit the reflector panel
correctly (see Installation
diagram).

Problem solving guide

48

«
...
46
47
48
49
50
...
»

Summary of Contents for Optima G 1470





































































Reviews:

No comments

Related manuals for Optima G 1470

CleanDesign GSD400T

Brand: GE Pages: 13

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: Pelgrim Pages: 32

Brand: Amica Pages: 28

1371236000 (0809)

Brand: Crosley Pages: 12

Brand: Frigidaire Pages: 14

Brand: Frigidaire Pages: 16

Brand: Frigidaire Pages: 24

Brand: Frigidaire Pages: 30

Brand: Frigidaire Pages: 32

Brand: Frigidaire Pages: 12

Brand: Frigidaire Pages: 11

Brand: Frigidaire Pages: 8

Brand: Frigidaire Pages: 2

Brand: Frigidaire Pages: 22

Brand: Frigidaire Pages: 3

Brand: Frigidaire Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands