Miele Optima G 1470 Operating Instructions Manual Download Page 58

Page: 58 / 68

Programme

When to use

Sensor wash

Sensor controlled programme
for

normally soiled

crockery

Quick wash 40 °C

"Quick programme" for

lightly soiled

crockery, e.g. party crockery;

for flushing out salt residues after replenishing the salt reservoir;
includes sensor controlled

glass care;

not suitable for tablet detergents.

Sensor wash
gentle

Sensor controlled

gentle programme

for

lightly soiled and temperature sensitive

crockery and glassware;

reduce detergent by 50%

Energy save

for

normal

everyday loads,

energy saving programme which uses a low temperature and long programme
duration;
includes sensor controlled

glass care

Pots & pans 75 °C for

normally soiled pots, pans, dishes etc

with

dried on

soiling;

for very heavy soiling, add 20% more detergent than recommended

Pre-wash

for rinsing crockery to avoid smells, if a complete cycle is not yet needed

1) Standard programme for energy labelling.
2) See "Operation, Display".
3) Depending on model.

Programme chart

Summary of Contents for Optima G 1470





































































Search results

Summary of Contents for Optima G 1470

Reviews:

Related manuals for Optima G 1470

Brands by name

Popular brands

Miele Optima G 1470, Operating Instructions Manual

Search results

Summary of Contents for Optima G 1470

Reviews:

Related manuals for Optima G 1470

Brands by name

Popular brands