Miele Novotronic Premier 520 Operating Instructions Manual Download Page 49 | Manualshive

Page: 49 / 68

background image

,

To avoid the risk of injury the

holes for the transit bars must be
covered after the transit bars have
been removed.

^

Fit the covers on to the two holes.
Then plug the holes as shown with
the caps.

^

Secure the transit bars to the back of
the washing machine. Make sure that
holes

b

are fitted over retainers

a

.

,

The washing machine must not

be moved without the transit bars in
place.
Store the transit bars as shown or
keep them in a safe place for future
use. They must be re-fitted if the
machine is to be moved again
(e.g.when moving house).

Re-fitting the transit bars

Re-fitting is carried out by reversing the
procedure.

Installation and connection

49

«
...
47
48
49
50
51
...
»

Summary of Contents for Novotronic Premier 520





































































Reviews:

No comments

Related manuals for Novotronic Premier 520

Brand: Haier Pages: 38

Brand: Rac Pages: 5

Brand: Gorenje Pages: 38

Brand: ZEP Pages: 36

Brand: Daewoo Pages: 38

Brand: GE Pages: 24

Brand: Silverline Pages: 88

Brand: Hotpoint Ariston Pages: 36

Brand: Campbell Hausfeld Pages: 60

Brand: Lavorwash Pages: 20

EVOconcept CCO-120DCW

Brand: Fagor Pages: 156

Brand: Gaggenau Pages: 52

AQUALTIS AQ9D 48 X

Brand: Hotpoint Ariston Pages: 48

Brand: Smeg Pages: 27

Brand: Buffalo Pages: 20

Brand: Bradley Pages: 5

Brand: Hotpoint Pages: 16

Brand: Hoonved Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands