Miele Novotronic Premier 520 Operating Instructions Manual Download Page 41 | Manualshive

Page: 41 / 68

background image

The drum door does not open when you press the Door button.

Problem

Remedy

The machine is not
connected to the
electricity supply.

Put the plug in the socket and switch on.

The washing machine is
not switched on.

Switch the machine on with the

I-On/0-Off

button.

Power cut.

Open the drum door as described in the section
"Opening the door in the event of a power failure".

The door was not
correctly engaged.

Press hard against the lock side of the drum door
and then press the

Door

button.

There is still water in the
drum and the machine is
unable to drain.

Clean the drain filter and the drain pump.

For safety reasons the drum door cannot be opened if the suds temperature is
higher than 55°C.

Problem solving guide

41

«
...
39
40
41
42
43
...
»

Summary of Contents for Novotronic Premier 520





































































Reviews:

No comments

Related manuals for Novotronic Premier 520

Brand: Kärcher Pages: 17

K 5 Full Control

Brand: Kärcher Pages: 16

Brand: Kärcher Pages: 12

K 3.800 eco!ogic

Brand: Kärcher Pages: 244

Brand: Kärcher Pages: 64

Brand: Kärcher Pages: 16

Brand: Kärcher Pages: 212

Brand: Kärcher Pages: 48

Brand: Kärcher Pages: 344

HDS-E 3.3/25-4M Ec

Brand: Kärcher Pages: 52

Brand: Kärcher Pages: 417

Brand: Kärcher Pages: 13

Brand: Kärcher Pages: 474

Brand: Kärcher Pages: 428

HDS 1.7/12 U Ed

Brand: Kärcher Pages: 48

Brand: Kärcher Pages: 352

Brand: Kärcher Pages: 11

HD 6/11-4 M Plus

Brand: Kärcher Pages: 372

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands