background image

Before you begin

Read these instructions completely
and carefully.
Have the appliance installed by a
qualified technician, according to
the enclosed installation
instructions.

To reduce the risk of injury or
damage to the product, two people
should be used for installation.

These installation instructions are
intended for use by qualified installers.
In addition to these instructions, the
appliance must be installed in
accordance with all local codes. In the
absence of a local code, the following
should be used:

– In the USA, the National Electric

Code, ANSI/NFPA 70 - latest
edition/State and Municipal codes
and/or local codes.

– In Canada, the Canadian Electric

code C22.1 - latest edition/Provincial
and Municipal codes and/or local
codes.

Tools needed for installation

– Cordless screwdriver

– Torx screwdriver

– Hammer drill

– Wood drills in different sizes

– Hammer

– Rachet 5/16" (8 mm)

– Adhesive tape

– Multi-grip pliers

– Level

– Tape measure

– Square

When fastening the cabinet to the wall
behind it (see "Installing the appliance")
use:

– suitable plugs/screws depending on

the type of wall.

– several mounting brackets, if required.

Other

– Stepladder

– Dolly, hand truck

– Wooden beam

(cross section min. 3" x 4"
[75 mm x 100 mm] as an alternative
tilt protection, length depends on the
width of the installation cavity)

– Wood screws in different sizes

Optional accessories

– "Merging Kit" for side-by-side installation

– Front panel gap kit

– RemoteVision module for wireless

monitoring

Installing the appliance

47

Summary of Contents for K 1803 Vi







































Reviews: