Miele H 5681 B Page 56 Operating And Installation Manual Download

Page: 56 / 84

Accessories

Baking tray, universal tray, anti-
splash insert (if applicable)

The surface has been treated with

PerfectClean enamel

Please refer to the section on
"PerfectClean" for information on
cleaning and care.

Rack, runners

The surface has been treated with

PerfectClean enamel

Treat in the same way as other surfaces
coated with PerfectClean. See
"PerfectClean".

Food probe

The food probe is dishwasher-safe.

FlexiClip telescopic runners

Do not clean FlexiClip telescopic
runners in a dishwasher. This would
remove the special lubricant.

When cleaning do not use:

– abrasive cleaning agents, e.g.

powder cleaners and cream
cleaners,

– stainless steel cleaning agents,

– hard, abrasive sponges and

brushes, e.g. pot scourers.

When cleaning the runners be very
careful not to wash out the special
lubricant in them.
Avoid frequent:

– soaking in hot soapy water,

– use of oven spray,

– cleaning of the bearings.

FlexiClip telescopic runners are best
cleaned after each use.
This prevents soiling drying on or being
burnt on when the oven is used again.

If the runners are used frequently
without being cleaned, it may become
very difficult or even impossible to
clean them.

Cleaning and care

Summary of Contents for H 5681 B





















































































Search results

Summary of Contents for H 5681 B

Reviews:

Related manuals for H 5681 B

Brands by name

Popular brands

Miele H 5681 B, Operating And Installation Manual

Search results

Summary of Contents for H 5681 B

Reviews:

Related manuals for H 5681 B

Brands by name

Popular brands