Miele G5930 Operating Instructions Manual Download Page 57

Page: 57 / 88

General problems

Problem

Possible cause

Remedy

The display is dark.

The dishwasher has
switched off
automatically to save
energy.

Switch the dishwasher on
again with the

sensor.

The interior lighting
does not come on when
the door is opened.

The lighting has been
switched off
permanently.

Switch the lighting back on
again (see "Additional
functions, BrilliantLight").

The following fault
message appears in the
display:

Salt reservoir cover
Close the salt reservoir

The buzzer sounds
during a programme.

The salt reservoir lid
has not been closed
properly.

– Close the salt reservoir lid

properly.

If the salt reservoir lid has
opened during a programme,
you must:

– Switch the dishwasher off

and then back on again
with the

sensor.

– Start the programme

again.

The buzzer sounds.
The following fault
message appears in the
display:

Middle spray arm blocked

Bottom spray arm blocked

Items are blocking the
path of the middle or
the bottom spray arm.

Open the dishwasher door
and rearrange the items
which are obstructing the
spray arm.

The middle or bottom
spray arm jets are
blocked.

– Switch the dishwasher off

with the

sensor.

Then:

– Clean the spray arm. See

"Cleaning and care".

Problem solving guide

Summary of Contents for G5930

























































































Search results

Summary of Contents for G5930

Reviews:

Related manuals for G5930

Brands by name

Popular brands

Miele G5930, Operating Instructions Manual

Search results

Summary of Contents for G5930

Reviews:

Related manuals for G5930

Brands by name

Popular brands