Miele G 8072 Operating Instructions Manual Download Page 40

Page: 40 / 52

Faults without "Err" in the display

Display

Problem

Cause/Effect

Remedy

–

You cannot switch
the appliance on

–

The machine is not
switched on at the
mains

–

Fuse defective or
tripped

Switch the
machine on at the
mains

Test the fuse and
change if
necessary, and
switch back on

–

Programme does
not start

–

Hood is not shut
correctly

–

Correct temperature
has not yet been
reached

Shut the hood

Wait until control

lights up green.

–

The dishes are not
clean

–

Not enough cleaning
agent, or cleaning
agent container is
empty

–

Basket filter and/or flat
filter dirty

–

Spray arm jets blocked

Fill up the
cleaning agent
container or add
more powder
detergent

Clean the basket
filter and/or flat
filter

Clean the spray
arm jets

Correcting minor faults

Summary of Contents for G 8072





















































Search results

Summary of Contents for G 8072

Reviews:

Related manuals for G 8072

Brands by name

Popular brands

Miele G 8072, Operating Instructions Manual

Search results

Summary of Contents for G 8072

Reviews:

Related manuals for G 8072

Brands by name

Popular brands