Miele G 7960 Operating Instructions Manual Download Page 83

Page: 83 / 128

Guide for selecting a programme

Gentle 45 °C



Auto 45–65 °C



QuickPowerWash 65 °C



ExtraQuiet 55 °C



QuickPowerWash 65 °C



+ Express



Programme

Hygiene 70 °C



The programmes can be combined with the “Express”, “IntenseZone”, “Extra clean” or

“Extra dry” extras (see the “Extras” chapter).

The estimated values may change due to the selected settings or programme options,

or the conditions in which the appliance is being used.

Consumption estimate

Energy consumption
Water consumption
Programme duration

Energy consumption
Water consumption

ECO 50 °C

Energy consumption
Water consumption
Programme duration

Programme duration

Intensive 75 °C



Energy consumption
Water consumption
Programme duration

Energy consumption
Water consumption

Programme duration 13 minutes,

no heating up,

solely for flushing out salt.

Programme duration

Summary of Contents for G 7960

































































































































Search results

Summary of Contents for G 7960

Reviews:

Related manuals for G 7960

Brands by name

Popular brands

Miele G 7960, Operating Instructions Manual

Search results

Summary of Contents for G 7960

Reviews:

Related manuals for G 7960

Brands by name

Popular brands