Miele G 7960 Operating Instructions Manual Download Page 49 | Manualshive

Page: 49 / 128

background image

Settings

49

Copyrights and Licences

Miele uses their own and third party
software which is not subject to any so-
called Open Source Licence for the op-
eration and control of the appliance.
This software/these software compon-
ents are protected by copyright. The
copyright powers of Miele and third
parties have to be respected.

Furthermore, this appliance contains
software components which are distrib-
uted under Open Source licence condi-
tions. Please refer to menu item

Set-

tings

|

Legal information

|

Open source li-

cences

in the appliance for the Open

Source components contained therein,
together with the corresponding copy-
right notices, copies of the licence
terms valid at the time, and any further
information. The liability and warranty
provisions of the Open Source licence
terms and conditions as stated therein
apply only in relation to the respective
rights holders.

Showroom

For demonstration purposes only.

The dishwasher is equipped with a
demo mode for showroom use.

Factory default

You can reset all dishwasher settings to
the factory default settings.

WiFi module settings (where applicable)
have to be reset separately (see “Set-
tings – Miele@home”).



Select

Reset appliance settings?

.



Select the

Yes

option and confirm

with

OK

.

«
...
47
48
49
50
51
...
»

Summary of Contents for G 7960

































































































































Reviews:

No comments

Related manuals for G 7960

Brand: Caloric Pages: 12

Brand: Maidaid Halcyon Pages: 17

Brand: Amica Pages: 52

Brand: ZANKER Pages: 40

Brand: Philco Pages: 51

Brand: Atag Pages: 40

Brand: Daewoo Pages: 42

Brand: Blomberg Pages: 40

Brand: Perlick Pages: 16

Brand: Gaggenau Pages: 28

Brand: AEG Pages: 52

Brand: AEG Pages: 28

Brand: AEG Pages: 24

Brand: AEG Pages: 72

Brand: AEG Pages: 24

Brand: CDA Pages: 36

Brand: AEG Pages: 72

Brand: AEG Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands