Miele G 7883 CD Operating And Installation Instructions Download Page 67

Page: 67 / 76

Removing the lid (if necessary)

Open the door.

Remove the fixing screws on both
sides using a cross slotted
screwdriver.

Pull the machine lid approx. 5 mm
forwards, lift upwards and remove.

Protecting the countertop

Important for machines with steam
condenser (depending on model):

To prevent steam damage to the
countertop, adhere the protective foil
9

" x 22

" (25 x 58 cm)

underneath the countertop near the
steam condenser.

Depending on the requirements for
installation, the following

kit

can be

ordered from the Miele Technical
Service Department.

Cover plate (protects the countertop)

The underside of the countertop is
protected from steam damage by a
stainless steel plate.

Installation

Summary of Contents for G 7883 CD













































































Search results

Summary of Contents for G 7883 CD

Reviews:

Related manuals for G 7883 CD

Brands by name

Popular brands

Miele G 7883 CD, Operating And Installation Instructions

Search results

Summary of Contents for G 7883 CD

Reviews:

Related manuals for G 7883 CD

Brands by name

Popular brands