Miele G 666 Operating Instructions Manual Download Page 33 | Manualshive

Page: 33 / 72

background image

Programme sequence indication

During the programme the programme
selector switch moves around the dial
to show which stage has been reached:

– Pre-wash (not shown)

– Wash cycle

– Interim rinse

– Final rinse

– Drying phase

The programme selector switch re-
mains stationary during the warm-up
phases of the wash and rinse cycle
until the required temperature has been
reached.

Note
Do not finish a programme prematurely.
Important programme stages (e.g. reac-
tivating the water softener) could be
omitted.

A programme is complete only when
the programme selector switch is at the
"End“ position.

You can now open the dishwasher and
unload it. If the dishwasher is left
closed, the drying fan runs on for a few
minutes to avoid condensation.

We recommend this if you do not need
the crockery immediately. This process
does not count as part of the main pro-
gramme time.

The PRE-WASH programme is com-
plete only when the programme selec-
tor switch stops just before the start
point of the "UNIVERSAL PLUS" pro-
gramme.

Programme change

– It is possible to change temperature

within a programme e.g. UNIVERSAL
55 ° to UNIVERSAL 65 °.

– If changing a programme e. g.

UNIVERSAL PLUS to UNIVERSAL or
from TOP SOLO to another pro-
gramme:
Turn the temperature selector switch
to "0-OFF".

Turn the programme selector switch
clockwise to the required Start point.

With the temperature selector switch
select the required temperature.

Programme interruption

A programme is interrupted as soon as
the door is opened.
If the door is closed again the pro-
gramme will continue from the position
it was at when it was interrupted.

Warning
Water in the dishwasher may be
hot. Danger of scalding!
Only open the door if absolutely
necessary and exercise caution
when doing so.
Before closing the door leave it ajar
for approx. 20 secs. This will en-
able the temperature in the wash
cabinet to settle. Close the door
firmly making sure that it clicks into
place.

Switching on and off

33

«
...
31
32
33
34
35
...
»

Summary of Contents for G 666









































































Reviews:

No comments

Related manuals for G 666

Brand: Hoover Pages: 144

Brand: ETNA Pages: 72

Brand: Gaggenau Pages: 36

Brand: Maytag Pages: 36

Brand: Indesit Pages: 16

Brand: Haier Pages: 22

Brand: Haier Pages: 40

Brand: Haier Pages: 19

WF21T6500 Series

Brand: Samsung Pages: 128

Brand: Haier Pages: 64

GE PTW600BPR DG Series

Brand: Haier Pages: 77

Brand: Häfele Pages: 101

Brand: Haier Pages: 36

Brand: GEAppliances Pages: 20

Brand: inventum Pages: 112

Brand: Bradley Pages: 4

Brand: AEG Pages: 56

Brand: Amica Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands