Miele G 349 Operating Instructions Manual Download Page 45 | Manualshive

Page: 45 / 64

background image

Problem

Possible cause

Remedy

The “End” and “Start”
indicator lights flash
simultaneously

There may be a technical
fault.

–

Turn the Programme
selector to the “Stop”
position.

–

Switch the dishwasher
off using the “On/Off”
button.

After a few seconds:

–

Switch the dishwasher
on using the “On/Off”
button.

–

Turn the Programme
selector to the required
programme.

–

Press the “Start” button.

If the indicator lights flash
again, there is a technical
fault.

–

Call the Miele Service
Department.

Despite the problem the
dishwasher can be used
in all programmes.
However the water will
not heat up.

Knocking noise in the
wash cabinet

The spray arm is
knocking against an item
in the basket.

Interrupt the programme,
rearrange items which
are obstructing the spray
arms.

Rattling noise

Items of crockery are
insecure in the wash
cabinet.

Interrupt the programme,
rearrange the items of
crockery.

Problem solving guide

45

«
...
43
44
45
46
47
...
»

Summary of Contents for G 349

































































Reviews:

No comments

Related manuals for G 349

Brand: Sammic Pages: 48

Brand: Samsung Pages: 132

Brand: Fisher & Paykel Pages: 56

SINGLE DISHDRAWER DD24SCTX9

Brand: Fisher & Paykel Pages: 3

Brand: Saturn Pages: 34

Brand: Zanussi Electrolux Pages: 16

Brand: CLEANVAC Pages: 8

Brand: GE Pages: 72

Brand: Baumatic Pages: 40

Brand: Fagor Pages: 115

Brand: Atag Pages: 44

Brand: Heinner Pages: 59

Brand: Bush Pages: 48

Brand: BALAY Pages: 26

SteamScrubber 45780 Series

Brand: Labconco Pages: 70

Brand: Indesit Pages: 12

Brand: Caple Pages: 24

Brand: Caple Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands