Miele G 1832 Operating Instructions Manual Download Page 36 | Manualshive

Page: 36 / 80

background image

Starting a programme

^

Select the

Start

option.

The programme starts, and the prompt

Crockery can be added

shows in the

display.
As long as this prompt is showing,
crockery can be added without
compromising the wash results.

A programme can only be cancelled
in the first few minutes. Otherwise
the programme must continue to the
end so that important programme
stages (e.g. reactivating the water
softener) are not omitted.

Time display

The duration of the programme
selected appears in hours and minutes
in the display before the programme
begins. During the programme, the
time left until the end of the programme
is displayed.

The time displayed may vary with the
same programme. This is partly
because of the water temperature at
each intake, and partly because of the
amount of crockery and how dirty it is.

When a programme is selected for the
first time, the display shows an average
time for a cold water intake.

The times shown in the Programme
Chart refer to standard test loads and
temperatures.

Each time a programme is run, the
electronic unit takes the new conditions
into account, and calculates the time
required.

Operation

36

«
...
34
35
36
37
38
...
»

Summary of Contents for G 1832

















































































Reviews:

No comments

Related manuals for G 1832

Brand: GE Pages: 2

Brand: Malber Pages: 16

Brand: Newworld Pages: 44

Brand: N'DUSTRIO Pages: 27

Brand: GE Pages: 28

Brand: NEFF Pages: 52

Brand: GE Pages: 72

Brand: Baumatic Pages: 40

Brand: Gaggenau Pages: 66

Brand: Furrion Pages: 26

Brand: SOGEDIS Pages: 16

Brand: Daewoo Pages: 7

Brand: DAEWOO ELECTRONICS Pages: 37

Brand: ZANKER Pages: 36

Brand: Alliance Laundry Systems Pages: 44

Brand: Smeg Pages: 2

FAV6800A Series

Brand: Maytag Pages: 13

Brand: Fisher & Paykel Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands