Miele G 1572 Operating Instructions Manual Download Page 51

Page: 51 / 68

Water inlet / drain fault

Problem

Possible cause

Remedy

The In-operation
indicator is flashing
quickly.
The buzzer is
sounding.
The Inlet/Drain
indicator flashes when
the door is open.

The stopcock is
closed.

–

Open the stopcock fully.

The dishwasher stops
during a programme.
The In-operation
indicator is flashing
quickly.
The buzzer sounds.
The Inlet/Drain
indicator flashes when
the door is open.
Fault code FXX shows
in the display.

Before rectifying the problem you
must:

–

Switch the dishwasher off with
the Off button

Faults F12/F13:
Water inlet
restricted.

–

Open the stopcock fully.

–

Clean the water inlet filter (see
"Maintenance").

–

The water pressure at the intake
is lower than 30 kPa (0.3 bar).
Seek professional advice.

Fault F11:
Water outlet is
restricted, water
remains in the
wash cabinet at
the end of a
programme.

–

Clean the filter combination. See
"Cleaning and care".

–

Clean the drain pump. See
"Maintenance".

–

Clean the non-return valve. See
"Maintenance".

–

Remove any kink in the drain
hose.

Problem solving guide

Summary of Contents for G 1572





































































Search results

Summary of Contents for G 1572

Reviews:

Related manuals for G 1572

Brands by name

Popular brands

Miele G 1572, Operating Instructions Manual

Search results

Summary of Contents for G 1572

Reviews:

Related manuals for G 1572

Brands by name

Popular brands