Miele F 1801 Vi Operating And Installation Instructions Download Page 55

Page: 55 / 76

If the indicator light does not come on,
installation of the module was
unsuccessful. In that case, repeat the
process. If that does not correct the
problem, contact Miele.

Pull the antenna

straight out.

Guide the cover

over the antenna

and screw on the cover.

Angle the antenna

so that it faces

to the right or left.

If necessary, disconnect the power
supply and continue installing the
appliance.

Preparing the installation
niche

Keep the appliance door closed
until it is securely fastened in the
niche. Tipping hazard.

If the installation niche is deeper than
the appliance, a solid wooden beam

can be placed behind the anti-tip
brackets

so the appliance can be

securely attached to the base or wall.

The length of the wooden beam

should be to the width of the installation
space.

If possible, always screw the
wooden beam into existing studs.

Installing the appliance

Summary of Contents for F 1801 Vi













































































Search results

Summary of Contents for F 1801 Vi

Reviews:

Related manuals for F 1801 Vi

Brands by name

Popular brands

Miele F 1801 Vi, Operating And Installation Instructions

Search results

Summary of Contents for F 1801 Vi

Reviews:

Related manuals for F 1801 Vi

Brands by name

Popular brands