manualshive.com logo in svg

Miele F 1801 Vi, Operating And Installation Instructions

Share
Download
Miele F 1801 Vi Operating And Installation Instructions Download Page 48

. . . with partition

If there is a partition between the
adjacent appliances, then each
appliance is to be individually installed
within its own niche.

The minimum thickness of the partition
is

5

/

8

" (16 mm).

A heating mat must only be installed if
the partition wall is less than 6"
(160 mm) wide.

For instructions on how to install the
heating mat please refer to the
instructions included in the "Merging
Kit".

The "Merging Kit" can be obtained
from Miele.

Side panels

If one side of the appliance is visible, a
side panel must be used.

The side panel must be firmly secured
to the wall, the floor and the overhead
furniture/fixtures before the appliance is
placed in the cavity.

The dimensions of the side panel are
taken from the opposite wall of the
installation space. During installation,
ensure that the cavity is square and the
measurements are correct.

Installation

48

Summary of Contents for F 1801 Vi













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands