Miele EcoSpeed&8kg TWF 760 WP Operating Instructions Manual Download

Page: 71 / 96

Installation

*INSTALLATION*

Changing the door hinging

You can change the door hinging on
this tumble dryer yourself.

For safety reasons the tumble dryer
must be disconnected from the elec-
tricity supply before changing the
door hinging.

You will need:

- a Torx T20 and T30 screwdriver

- a flat head screwdriver or pointed pli-

ers

- the lock catch cover supplied

- the door hinge cover supplied

- a soft surface (e.g. a tablecloth)

Changing the hinging over

1. Remove the door from the dryer



Open the door.



Use a T30 Torx screwdriver to un-
screw the two screws on the base
plate of the door hinge



The door cannot fall off as it is held in
place by 2 pins.



Hold the door securely and pull it for-
wards: to remove the door you will
need to pull the base plate of the
hinge with its 2 pins out of the dryer.

To avoid scratching the door, place it
outer side downwards on a soft sur-
face (e.g. a tablecloth).

2. Change over the door lock on the
dryer



Use a Torx T30 screwdriver to un-
screw the two screws on the door
lock





Use the screwdriver to press the door
lock upwards.

The door lock will spring out of its posi-
tion and can then be removed.

Summary of Contents for EcoSpeed&8kg TWF 760 WP

































































































Search results

Summary of Contents for EcoSpeed&8kg TWF 760 WP

Reviews:

Related manuals for EcoSpeed&8kg TWF 760 WP

Brands by name

Popular brands

Miele EcoSpeed&8kg TWF 760 WP, Operating Instructions Manual

Search results

Summary of Contents for EcoSpeed&8kg TWF 760 WP

Reviews:

Related manuals for EcoSpeed&8kg TWF 760 WP

Brands by name

Popular brands