Miele EcoSpeed&8kg TWF 760 WP Operating Instructions Manual Download

Page: 12 / 96

Warnings and safety instructions



The R290 refrigerant contained in this tumble dryer is flammable

and explosive. If the tumble dryer is damaged, proceed as follows:

- Avoid naked flames or anything which creates a spark.

- Disconnect the tumble dryer from the electrical supply.

- Air the room where the tumble dryer is located.

- Contact the Miele Customer Service Department.



Risk of fire and explosion due to damage to the tumble dryer.

The refrigerant is flammable and explosive if it leaks.

Take measures to protect the tumble dryer against damage. Do not
make any alterations to the tumble dryer.



Follow the instructions in “Installation” and “Technical data”.



The accessibility of the plug must always be ensured, in order to

disconnect the tumble dryer from the mains.



Do not block the gap between the bottom of the tumble dryer and

the floor with plinth facings, deep pile carpet etc. This would hinder a
sufficient flow of air to the dryer.



Make sure the dryer door can be opened without hindrance after

installation.

Correct use



The maximum load for this tumble dryer is 8.0 kg (dry weight).

The maximum recommended loads for individual programmes are
given in the Programme chart.



To prevent the risk of fire, do not connect the tumble dryer via a

controllable socket (e.g. a timer or a peak-load switch-off device).
If the drying programme is interrupted before the end of the cooling
down phase, this could cause the laundry to self-ignite.

Summary of Contents for EcoSpeed&8kg TWF 760 WP

































































































Search results

Summary of Contents for EcoSpeed&8kg TWF 760 WP

Reviews:

Related manuals for EcoSpeed&8kg TWF 760 WP

Brands by name

Popular brands

Miele EcoSpeed&8kg TWF 760 WP, Operating Instructions Manual

Search results

Summary of Contents for EcoSpeed&8kg TWF 760 WP

Reviews:

Related manuals for EcoSpeed&8kg TWF 760 WP

Brands by name

Popular brands