Miele EcoSpeed&8kg TWF 760 WP Operating Instructions Manual Download

Page: 46 / 96

Cleaning and care



Remove the fluff from the filter sur-
face of all the fluff filters and the per-
forated laundry deflector.



Push the upper fluff filter back into
position until it clicks.



Close the door.

Cleaning the fluff filters and air flow
openings thoroughly

If the drying duration has become
longer or the surface of the filters is
visibly compacted with fluff, you
should carry out the following cleaning
procedure.



Remove the fragrance flacon. See
“Fragrance flacon”.



Pull the upper fluff filter forwards to
remove it.



Turn the yellow dial on the lower fluff
filter in the direction of the arrow (until
it reaches the stop position).



Hold the dial and pull the fluff filter
forwards to remove it.

Summary of Contents for EcoSpeed&8kg TWF 760 WP

































































































Search results

Summary of Contents for EcoSpeed&8kg TWF 760 WP

Reviews:

Related manuals for EcoSpeed&8kg TWF 760 WP

Brands by name

Popular brands

Miele EcoSpeed&8kg TWF 760 WP, Operating Instructions Manual

Search results

Summary of Contents for EcoSpeed&8kg TWF 760 WP

Reviews:

Related manuals for EcoSpeed&8kg TWF 760 WP

Brands by name

Popular brands