manualshive.com logo in svg

Miele DA 6690 D, Operating And Installation Instructions

Share
Download
Miele DA 6690 D Operating And Installation Instructions Download Page 32

,

Before installation, it is important

to read the information given on the
following pages as well as the
"Appliance dimensions" and the
"Warning and safety instructions" at
the beginning of this booklet.
This is particularly crucial when
using the cooker hood at the same
time as a heating appliance that
relies on oxygen from the same
room to avoid the danger of toxic
fumes building up.

Installation accessories

4 screws 7 x 110 mm

and

4 plugs 10 x 80 mm

for securing the

cooker hood to the ceiling.

,

The plugs are approved to

European technical standards for
use in concrete ceilings. Only use
the plugs in combination with the 7 x
110 mm screws supplied.
For other types of ceilings use the
appropriate fixing materials.
Make sure the ceiling is strong
enough to bear the weight of the
cooker hood.

4 clamps

for adjusting and securing

the extension piece

4 screws M4 x 8.5 mm

for securing the

clamps

14 screws M4 x 8 mm

for securing the

spacer frame and the cooker hood to
the installation frame.

1 screw M4 x 16 mm

for securing the

tower.

Conversion kit DUI 32 for
recirculation mode

(not supplied,

optional accessory). The kit contains a
directional unit and flexible aluminium
ducting with hose clips.

Installation

32

Summary of Contents for DA 6690 D

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands