Miele DA 390-6 Operating Instructions Manual Download | Manualshive

Page: 33 / 48

background image

Installation

33



Fit the four telescopic piece clamps.

When the screws are tightened, the

clamps spread out and push the

telescopic piece upwards.

Tighten the screws only until the top

edge of the telescopic piece is

evenly aligned with the ceiling or the

spacer frame.



Bend back the two retaining tabs.



Push the tower over the telescopic

piece and bend the retaining tabs

outwards again to prevent the tower

from slipping down again.

«
...
31
32
33
34
35
...
»

Summary of Contents for DA 390-6

















































Reviews:

No comments

Related manuals for DA 390-6

Brand: Dacor Pages: 52

Brand: ETNA Pages: 50

Brand: Maico Pages: 60

Brand: Dacor Pages: 12

Brand: Gaggenau Pages: 16

Brand: AIRFORCE Pages: 94

Brand: Windster Pages: 16

Brand: NEFF Pages: 16

Design Plane 90 Inox

Brand: FALMEC Pages: 59

Brand: NuTone Pages: 28

Brand: Electrolux Pages: 36

Brand: Electrolux Pages: 20

Brand: Electrolux Pages: 16

Brand: Electrolux Pages: 18

Brand: Electrolux Pages: 20

Brand: Electrolux Pages: 4

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands