Miele CVA 744C Operating And Installation Instructions Download Page 76

Page: 76 / 88

Problem solving guide



Connect the angular moulded hose to
the longer milk pipework. Firstly fit
the moulded hose at the top on the
central spout. The black connection
piece should point towards the rear.



Connect the lower end of the
moulded hose to the dispensing unit
on the central spout.



Insert the milk pipework into the milk
valve on the left and right-hand sides.



Check whether the milk pipework sits
comfortably against the housing and
the cover is easy to refit.

Useful tip:

If necessary, turn the milk

pipework on the right towards the back.



Fit the milk valve cover: to do this,
place the pin in the top right corner
and swing the cover towards the rear
until it closes flush.



Refit the bean container on the left
and the maintenance container in the
coffee machine. Refit the central
spout stainless steel cover



Close the appliance door.

Summary of Contents for CVA 744C

























































































Search results

Summary of Contents for CVA 744C

Reviews:

Related manuals for CVA 744C

Brands by name

Popular brands

Miele CVA 744C, Operating And Installation Instructions

Search results

Summary of Contents for CVA 744C

Reviews:

Related manuals for CVA 744C

Brands by name

Popular brands