background image

ERR WATER-PRG
Programming fault: more than one
water inlet valve has been activated in
one program step, or an inlet valve has
not been activated in combination with
the circulation pump.

ERR WATERINF
Water inflow time is insufficient.
Increase the ADD-WATER time in the
system parameters.

ERR BATTERY

Change the lithium battery within 4
weeks after this message.

^

If possible, reset the fault and start
the program again.

When the following

operating

messages

appear in the display, the

appropriate action must be taken:

GROBFILTER (PREFILTER)

Change the coarse filter in the drying
unit (see page on drying unit
maintenance). Then reset the filter
display message.

^

Key switch position III or IV.

^

Use touch pad

O

or

M

to select

program 12 GROBFILTER (Coarse
filter).

^

Press the START button.

FEINFILTER (HEPA-Filter)

Call the Miele Technical Service Dept to
change the particle filter in the TA
drying unit. (See page on drying unit
maintenance.)

REGENERIER (REGENERATE)

Replenish the water softener with salt
(see Reactivating water softener).

Interrupting a program

Once a program has been started, it
should only be interrupted in an
emergency or if the items are moving
about noisily due to incorrect loading.

The machine must be turned off, the
water drained from the wash cabinet
and the program re-started.

^

Turn the main switch to 0 (off).

^

Wait 5 seconds, the turn the main
switch to I (on).

DRAIN is displayed if there is water in
the machine (the water is then pumped
away).

OR

the program parameters are

displayed with a flashing step time (no
water in the machine).

^

Key switch position II.

^

Press the RESET touch pad.

^

Open the door and arrange the items
properly.

^

Shut the door.

^

Start the program again.

Turning off

On completion of the program the ON
indicator light

l

goes out. If the

machine is not to be used again:

^

Turn the main switch to 0 (off). This
disconnects the machine from the
main power supply.

^

Turn off the faucets (water supply).

Operation

18

Summary of Contents for IR 6001















































Reviews: