manualshive.com logo in svg

Midtronics psc-700, Instruction Manual, Page: 11 / 16

Share
Download
Midtronics psc-700 Instruction Manual Download Page 11

11

www.midtronics.com

POWER CHARGE

™

 PSC-700

Protection Features

Each Power Charge power supply/maintenance charger is designed with high 

quality components to help ensure years of continuous use. The Power Charge is 

protected by multiple protection features for a long, trouble-free life:

 

•

Reverse battery polarity protection. (Note: The green LED on the On/Off 

switch does not light when the Power Charge is connected in reverse po-

larity.

 

•

Brownout input protection. 

 

•

Over-current protection: cycle-by-cycle peak-limiting, as well as rated cur-

rent-limiting, to maximize the life of the Power Charge. 

 

•

Over-temperature protection. 

In addition, the Power Charge is designed with a unique “proportional” fan-

control circuit. Fan speed is directly proportional to the Power Charge’s internal 

ambient temperature. This enables the fan to turn on and off very slowly, 

minimizing unwanted fan-starting noise.

Charger Location

The Power Charge PSC-700 must be located in an area with sufficient air space 

to allow unrestricted airflow in and around the charger.
Not for permanent installation: Modifying this charger for permanent 

installation in a vehicle or installing this charger in a vehicle for permanent use 

is not recommended.

In the event of fail device may gen-

erate and emit sparks.

Only charge rechargeable flooded 

maintenance-free, low-maintenance or 

deep-cycle batteries.

The PSC-700 is not designed for wet location mounting and must be protected 

from direct contact with water.

Summary of Contents for psc-700

















Reviews:

No comments