background image

Midtronics B.V.     Hoofdveste 6 - 8     Houten NL

www.midtronics.com

EXP-1000 HD

Chapter 4: Battery Test

The tester guides you through the steps of selecting your 

battery test parameters and interpreting the results. Before 

you start the test, review the instructions in 

Chapter 3: Test 

Preparation

1.  Select the BATTERY LOCATION.

 OUT OF VEHICLE

 IN VEHICLE

Press the NEXT soft key to continue.

2.  Select the VEHICLE TYPE.

 TRUCK

 CAR / VAN

Press the NEXT soft key to continue.

3.  In case of IN-VEHICLE please select the NUMBER OF BAT-

TERIES.

 1

 2

4.  Select the BATTERY TYPE.

 REGULAR

 AGM

 SPIRAL

 GEL

Press the NEXT soft key to continue.

5.  Select the battery’s capacity rating standard. The stan-

dard, and the rating units required are printed on the bat-

tery label. If the information is unreadable, contact the 

battery manufacturer.  

 CCA

 JIS

 DIN

 SAE

 IEC

 EN

Battery Standards

Rating 

System

Description

Range

CCA

Cold Cranking Amps (specified 

by SAE): The amount of 

current a battery can provide at 

0 ºF (–17.8 ºC).

100 to 1700

JIS

Japanese Industrial Standard: 

(shown on a battery as a 

combination of numbers and 

letters.

73 numbers 

from 26A17 

to 245H52

DIN (A) Deutsche Industrie-Norm

100 to 1000

SAE (A) European labeling of CCA

100 to 1700

IEC (A)

International Electrotechnical 

Commission

100 to 1000

EN (A)

European Norm

100 to 1700

If you select JIS, the analyzer asks for the JIS part number. 

Scroll to the part number. To increase your scrolling 

speed, hold the UP (

) or DOWN (

) ARROW key, or use 

the LEFT (

or RIGHT (

) ARROW key to move up or 

down four part numbers at a time.

Press the NEXT soft key to continue.

6.  Press an UP (

) or DOWN (

) ARROW key or use the 

numeric keys to select the BATTERY RATING, or in the case 

of JIS, the part number. To increase your scrolling speed, 
hold down the 

UP

 or 

DOWN ARROW key.

500

CCA

Press the NEXT soft key to continue.

7.  Select the TEMPERATURE

Aim the tester 5 cm from the sides or top of the battery 

case. As soon as the temperature reading is stable the 

operator can press NEXT.

The tester will now test the battery.

For the next few seconds the tester will display the word 

TESTING and a stopwatch while it evaluates the battery.

Chapter 4: Battery Test

Summary of Contents for EXP-1000 Heavy Duty



























Reviews: