background image

Titan

 Mobile User’s Guide

 

 

©

 2005, Midland Radio Corporation

 

19

 

priority channel. This is the primary difference between Public 
Safety scan and Priority scan.  

If activity is detected on a channel, the radio will pause scan and 
display that channel. While stopped on a non-priority channel, 
the radio will continue to check for activity on the priority 
channel(s). This is called 

priority channel lookback

, and the 

receive audio from the non-priority channel will be briefly 
interrupted while priority lookback occurs. While the radio is 
stopped on a non-priority channel it may be deleted from the 
scan list by briefly pressing the A/D button. This is the 

nuisance 

channel delete 

function. The priority channel(s) can not be 

deleted from the scan list. To resume scanning at the next 
channel in the scan list, without deleting the channel, rotate the 
channel/menu knob clockwise. 

Priority Monitor Mode (Dual watch) 

Priority Monitor mode is available when your dealer has 
programmed 

Second

 

Scan Selection

. Use the menu function to 

select PRI scan mode. 

 

The default user selection is PRI scan mode. User selections of SCN 

(Busy scan) and P/S (Priority scan) are also possible when your dealer 
has programmed Second Scan Selection. 

If enabled in programming, you may assign a second priority 
channel before initiating priority monitoring. Select the desired 
second priority channel using the channel selector, then press 
and hold the SCAN button for two seconds. The channel display 
will flash when a second priority channel is displayed. 

Press and release SCAN to activate Priority Monitor mode. The 
channel selected when priority monitoring is started will be 
assigned as the first priority channel. Then use the 
channel/menu knob to select a channel of operation, while 
continuing to monitor the priority channel(s) for activity. While in 
Priority Monitor mode, the radio will normally display the 
operating channel and the PRI icon. 

Summary of Contents for 700671C





























Reviews: