Midian TRA, Instruction Manual

Page: 14 / 20

Enter Programming Access Code: 2 7 1 8 2 8 1 8 2 8 4 on telephone keypad (see Section 3)
For this feature
Enter These Codes
Decode Number 1 (1-8 digits) plus Ring Code (1 digit)
Enter the desired decode number plus Ring Code. The last digit entered will become
the ring code. For example, if the desired decode number is 12345 with ring code 1,
enter the sequence 123451 followed by * 01.
* 01
* 02
Decode Number 2 (1-8 digits) plus Ring Code (1 digit)
Program in the same manner as Decode Number 1.
Decode Number 3 (1-8 digits) plus Ring Code (1 digit)
Program in the same manner as Decode Number 1.
* 03
Connect ANI (0-8 digits)
This will be transmitted when PTT is pressed and/or released, depending on the
ANI Position setting in Transmit Parameters .
* 04
* 05
Disconnect ANI (0-8 digits)
Program in the same manner as Connect ANI.
Transpond (0-8 digits)
This sequence will be transponded only on decode of Decode Number 1; this prevents
"mid-air collisions" on group call.
Note: The Auxiliary Input in Transmit Parameters
turns transpond ON or OFF.
* 06
ANI/Secondary Dialing Format & Tone Lengths (11 digits)
A) Number of Digits (1-9, 0=any)
Sets
the number of digits accepted in the Secondary Dialing Format ; 0 disables this feature.
B) ANI Format (00-60; see table 4)
Enter the two digit code that corresponds to the desired format from Table 4.
C) Time 1 (0.000-9.999 seconds)
Enter the desired time for the first tone. This separate timing makes possible a
preamble tone. If nothing is entered, industry standard timings will be used.
D) Time 2 (0.000-9.999 seconds)
Enter the desired time for subsequent tones. If nothing is entered , all tones will be
encoded for the length that is entered in
Time 1 .
* 07
Primary Dialing Format & Tone Lengths (11 digits)
A) Number of Digits (1-9, 0=any)
Sets
the number of digits accepted in the Primary Dialing Format ; 0 disables this feature.
B) Dialing Format (00-60; see table 4)
Program in the same manner as ANI/Secondary Format & Tone Lengths .
C) Time 1 (0.000-9.999 seconds)
Program in the same manner as ANI/Secondary Format & Tone Lengths .
D) Time 2 (0.000-9.999 seconds)
Program in the same manner as ANI/Secondary Format & Tone Lengths .
* 08
Transpond Format (10 digits)
A) Transpond Format (00-60; see table 4)
Program in the same manner as ANI Format & Tone Lengths .
B) Time 1 (0.000-9.999 seconds)
Program in the same manner as ANI Format & Tone Lengths .
C) Time 2 (0.000-9.999 seconds)
Program in the same manner as ANI Format & Tone Lengths .
* 09
Decode Format & Tone Detect Time (6 digits)
A) Decode Format (00-60; see table 4)
Program in the same manner as ANI Format & Tone Lengths .
B) Time 1 (0.000-9.999 seconds)
When using DTMF, this is an interdigit timer. We recommend 1-2 seconds. When
using 5-tone, enter a time that is 1/5 of the encode tone time in increments of 5
ms.
For example, if the encode time is 25 ms/ tone, set the decode time to 5 ms/tone.
* 10