3
4
Function Buttons
ON/OFF
Button
Button
SET Button
OK Button
Button
Button
Turns the unit on or off
Used to confirm the
selected functions
Adjust
Adjust
Increases temperature in
O
O
0.5 C(1 F) increments.
Hold down this button to
increase temperature in
O
O
1 C(1 F) increments. Max.
Temperature is
o
O
30 C(86 F).
Decreases temperature
O
O
in 0.5 C(1 F) increments.
Hold down this button
to decrease temperature
O
O
in 1 C(1 F) increments.
Min. temperature is
O
O
16 C(60 F).
ECO/GEAR Button
Boost Button
Starts and stops the horizontal
louver movement.
Starts and stops the vertical
louver movement.
Scrolls through operation
functions as follows:
Scrolls through operation
functions as follows:
Breeze Away Breeze Mild
Breezeless Cancel
Breeze Away .......
NOTE:
This feature is available
under cooling mode only.
Turns indoor unit s LED
display and air conditioner
buzzer on and off, which
create a comfortable and
quiet environment.
NOTE: Press this button
seven times in 10 seconds
to enter into AP mode
(if applicable).
MODE Button
Scrolls through operation
modes as follows:
Active clean ( ) Sleep( )
Follow Me( )
g
g
g
g
g
g
g
,
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote
control. The following is a brief introduction to the remote control itself. For instructions on how to
operate your air conditioner, refer to the
How to Use Basic Functions
section of this manual.
NOTE
：
Please do not select HEAT mode if the machine you purchased is cooling only
type. Heat mode is not supported by the cooling only appliance.
AUTO
g
COOL
g
DRY
g
HEAT
g
FAN
NOT SURE WHAT A FUNCTION DOES?
Refer to the
How to Use Basic Functions
and
How to Use Advanced Functions
sections of this manual for a detailed
description of how to use your air conditioner.
SPECIAL NOTE
Button designs on your unit may differ
slightly from the example shown.
If the indoor unit does not have a particular
function, pressing that function s button on
the remote control will have no effect.
TIPS FOR USING REMOTE CONTROL
The remote control must be used within 8
meters of the unit.
The unit will beep when remote signal is
received.
Curtains, other materials and direct
sunlight can interfere with the infrared
signal receiver.
Remove batteries if the remote control
will not be used more than 2 months.
INSERTING AND REPLACING BATTERIES
INSTALLING REMOTE CONTROL HOLDER
Put the two batteries(optional parts) in the remote
control before use:
1. Remove the back cover from the remote
control, exposing the battery compartment.
2. Insert the batteries, paying attention to
match up the (+) and (-) ends of the
batteries with the symbols inside the
battery compartment.
3. Install the back cover on.
The remote controller can be attached to a wall
or stand by using a remote controller holder.
Before installing the remote controller, check
that the air conditioner receives the signals
properly.
the remote controller on the holder.
1.
2. Install the holder with two screws.
3. Put
BATTERY NOTES
For optimum product performance:
Do not mix old and new batteries, or
batteries of different types.
Do not leave batteries in the remote control
if you don t plan on using the device for
more than 2 months.
BATTERY DISPOSAL
Do not dispose of batteries as unsorted
municipal waste. Refer to local laws for
proper disposal of batteries.
,
,
Handling The Remote Controller
Remove the back cover
to install batteries
The selected symbol will flash
on the display area, press the
OK button to confirm.
Enables unit to reach preset
temperature in shortest
possible time
FAN SPEED
TIMER Button
Selects fan speeds in the
following order:
Set timer to turn unit on or off
(see page 9 )
AU
g
g
20%
60%
40%
80% 100%.
g g
g
Press the Adjust or
button to increase /decrease
the fan speed in
1%
increments.
Press this button to
enter the energy efficient
mode in a sequence of
following: ECO GEAR(75%)
GEAR(50%) Previous
setting mode ECO
......
