Midea MFA-12HRDN1-Q, Manual

Page: 20 / 22

18
installation & owner’s manual
All signs shown in the Fig.2 is for the purpose of clear
presentation. But during the actual operation only the
relative functional items are shown on the display panel.
Due to the difference of the set temperature of the unit
and the actual indoor temperature, the Air Conditioner
when in DRY mode will automatically operate many
times without running the COOL and FAN mode.
The FAN ONLY mode can not be used to control the
temperature. While in this mode, only steps 1,3 and 4
may be performed.
In the AUTO mode, the air conditioner can logically
choose the mode of COOL, FAN , HEAT and DRY by
sensing the difference between the actual ambient room
temperature and the set temperature on the remote
controller.
If the AUTO mode is not comfortable for you, the desired
mode can be selected manually.
4. Operating the Remote Controller
To install the batteries, slide the back cover of the battery
compartment and install the batteries according the direct-
ion (+and -)shown on the Remote Controller.
To replace the old batteries, use the same method as ment-
ioned above.
1.
2.
Push the MODE button to select DRY.
Push the TEMP button to set the desired temperature
from 21
ć to 28 ć .
Push the ON/OFF button, the operation lamp lights and the
air conditioner start to operate in the DRY mode. FAN
SPEED is Low. Push the ON/OFF button again to stop this
unit operation.
TIMER ON button can set the auto-on time of the unit..
TIMER OFF button can set the auto-off time of the unit.
1.
2.
3.
Push the TIMER ON button, then the remote controller
shows TIMER ON , the last set time for the starting
operation and the signal "h" will be shown on the DIGITAL
DISPLAY area. You are now ready to reset the time to
START the operation.
Push the TIMER ON button again to set desired unit start
time.
After setting the TIMER ON ,there will be a one-half
second delay before the remote controller transmits the
signal to the air conditioner. Then, after approximately
another 2 seconds, the signal "h" disappears and the set
temperature will re-appear on the digital display.
1.
2.
3.
The Remote Controller uses two alkaline dry batteries
(LR03X2).
Use the MODE .select button to select AUTO.
Push the TEMP button to set the desired room temperature.
The most comfortable temperature setting are between 21
ć to 28 ć
Push the ON/OFF button to start the air conditioner. The
OPERATION lamp on the display panel of the indoor unit
lights. The operating mode is AUTO FAN SPEED is auto-
matically set and there are no indicators shown on the
display panel of the remote controller.
Push the ON/OFF button again to stop the unit operation.
1.
2.
3.
4.
If the AUTO mode is not comfortable, you may manually
override the settings by using COOL, HEAT or FAN ONLY
modes.
Push the TEMP button to set the desired room
temperature. When in COOL mode, the most comfortable
settings are 21
ć
or above. When in HEAT mode, the
most comfortable settings are 28
ć
or below.
Push the FAN SPEED to select the FAN mode of AUTO,
HIGH,MED or LOW.
Push the ON/OFF button, the operation lamp lights and
the air conditioner start to operate as your settings. Push
the ON/OFF button again to stop this unit operation.
1.
2.
3.
4.
When the Air Conditioner is ready for use, switch on the
power and the OPERATION indicator lamp on the display
panel of the indoor unit starts flashing.
To set the starting time.
Push the TIMER OFF button and the remote controller
will show TIMER OFF, the last set time for the stopping
operation and the signal "h" will be shown on the DIGITAL
DISPLAY area.You are now ready to reset the time of the
STOP operation.
Push the TIMER OFF button again to set the time you
want to stop the operation.
After setting the TIMER OFF ,there will be a one-half
second delay before the remote controller transmits the
signal to the air conditioner. Then, after approximately
another 2 seconds, the signal "h" disappears and the set
temperature will re-appear on the digital display.
1.
2.
3.
To set the stopping time.
4.1 Install/Replace Batteries
4.2 AUTOMATIC OPERATION
4.3 COOL/ HEAT (Cooling only model withou-
t) and FAN ONLY Operation
4.4 DRY Operation
4.5 TIMER Operation
NOTE
NOTE NOTE
NOTE