Midea MFA-12HRDN1-Q, Manual

Page: 19 / 22

17
installation & owner’s manual
REMOTE CONTROLLER MANUAL
COOL only model has no HEAT feature.
The unit will automatically revert back to the previous
operational mode after continuously operating under the
powerful cooling mode.
1. Remote Controller Specifications
2. Introduction of Function Buttons on the
Remote Controller
3. Names and Functions of indicators on
Remote Controller
TEMP Button : Press the button to decrease the indoor
temperature setting.
TEMP Button : Press the button to increase the indoor
temperature setting.
ON/OFF Button: Push this button to start the unit operati-
on.Push the button again to stop the unit operation.
MODE Select Button: Each time you push the button, a
mode is selected in a sequence that goes from AUTO
ǃ
COOL
ǃ
DRY
ǃ
HEAT and FAN, as the following figure
indicates:
SWING Button: Push this button, the louver would swing
up and down automatically. Push again to stop it .
RESET Button: Press When the RESET button is
pushed, all of the current settings are cancelled and the
control will
return to the initial settings.(Use a
¶
1mm little
round stick to push the button )
AIR DIRECTION Button: Push this button, the louver can
be fixed at a desired angle. The louver swing(upward
or downward
) to a certain angle for each press. When
the louver swing at an angle which would affect the
cooling and heating efficiency of the air conditioner, it
would automatically change the swing direction (upward
or downward).
Model
Environment
Reaching Distance
Signal Range
Lowest Voltage of CPU
Emitting Signal
Rated Voltage
R51D/E ˈ R51D/CE
-5
ć
~60
ć
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Alkaline dry batteries LR03 2)
2.0V
Fig. 1
1 2
4
6
7
1
2
3
4
5
FAN SPEED Button: This button is used for setting Fan
Speed in the sequence that goes from AUTO
ǃ
LOW
ǃ
MED to HIGH, then back to Auto.
TIMER ON Button: Press this button to preset the time
ON(start to operate). Each press will increase the time ON
setting in 30 minutes increments. When the setting time
displays 10:00, each press will increase the time ON setting
in 60 minutes increments.To cancel the time ON program,
simply adjust the time ON to 0:00.
ECONOMIC RUNNING Button: Press this button to go into the
Energy-Saving operation mode. Press the button again to
cancel.
TIMER OFF Button: Press this button to preset the time
OFF (turn off the operation). Each press will increase the
time OFF setting in 30 minutes increments. When the
setting time displays 10:00, each press will increase the
time OFF setting in 60 minutes increments. To cancel the
time OFF program, simply adjust the time OFF to 0:00
LOCK Button: Push this button to lock in all the current
VHWWLQJV7RUHOHDVHVHWWLQJVSXVKDJDLQ8VHDijPP
little round stick to push this button )
POWERFUL Button: Press this button on cooling/heating
mode to go into powerful cooling (heating)operation.Press
again to cancel it.
8
9
10
11
12
13
6
7
5
6
7
3
8
9
10
11
12
13
SET TEMPERATURE
㨭㨲 O
C)
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
TEMP.
MODE
ON/OFF FAN SPEED
SWING ECONOMIC TIMER ON
RESET LOCK
TIMER OFF
AIR DIRECTION
POWERFUL
5
AUTO COOL DRY
HEAT
FAN
DIGITAL DISPLAY area: This area will show the temperat-
ure and, if in the TIMER mode, will show the ON and OFF
settings of the TIMER. It will automatically revert back to
show the temperature after 5 seconds. Under "FAN" oper-
ation mode,nothing is shown in this area.
TRANSMISSION Indicator: This indicator flashes once
when remote controller transmits signals to the indoor unit.
ON/OFF Indicator: This symbol appears when the unit is
turned on by the remote controller, and disappears when
the unit is turned off.
OPERATION MODE Indicator: Shows the current operat-
ion modes--"AUTO", "COOL", "DRY", "HEAT" and "FAN".
HEAT only available for heat pump model.
FAN SPEED Indicator: Press the FAN SPEED button to
select the desired fan speed setting (Auto-Low-Med- High).
You selection will be displayed in the LCD window except
the Auto fan speed.
LOCK Indicator: This symbol appears when press the
LOCK button, and disappears when press it again.
TIMER ON/OFF Display: This display area shows the
settings of TIMER. That is, if only the starting time of
operation is set, it will display the TIMER ON. If only the
turning off time of operation is set, it will display the TIMER
OFF. If both operations are set, it will show TIMER ON/ OFF
which indicates you have chosen to set both the starting time
and off time.
1
2
3
4
1
2
4
6
7
5
4
3
Display Panel
TIMER ON/ OFF
NOTE
NOTE