background image

 

Maintenance Service and Trouble Shooting   

ambient temperature ,this means that most meshes of its screen has been 

 

clogged ,resulting in an obstructed flowing of refrigerant ,thus causing a 

 

drop in temperature due to throttling . 

 

d)    Feel the temperature of exhaust gas from the refrigerating 

 

system .the exhaust gas should be very hot and this is the normal working 

 

state .For those appliance with enclosed type of compressor refrigerating 

 

system, no frost or dew drop will from on the gas suction 

 

tube ,otherwise ,there is something wrong in the system (Frosting and dew 

 

condensation may appear for a very short time period when just starting the 

 

machine ,this is a normal phenomenon ). 

 

Because a appliance is a combination of several components ,they are 

 

related and have influence on each other In case an abnormal 

 

phenomenon has been found through the above-mentioned checkups ,you 

 

need not to make a hasty conclusion based on only one abnormal 

 

phenomenon .It is advisable to find out two or more abnormal 

 

phenomenon ,or conduct troubleshooting comprehensively with the aid of 

 

instruments or other ways ,because several kinds of troubles may share a 

 

common abnormal phenomenon ,and two or more abnormal phenomena 

 

may occur simultaneously due to a certain trouble .With this method ,you 

 

can reject some suspicious troubles and finally make a correct judgment . 

 

7 Analysis of Troubles and Troubleshooting 

 

A.   Poor Refrigerating Effect 

 

The so-called "poor refrigerating effect " refers to the fact that the 

 

appliance can operate and appliance normally ,but the temperature in 

 

the appliance cannot drop to the prescribed value under the stipulated 

 

working conditions .In view of there are many causes for this 

 

phenomenon ,we are going to discuss and analyze it in the following 7 

 

aspects : 

 

1)   Leakage of refrigerant 

 

Analysis of Trouble 

 

The leakage of refrigerant in the system will result in an insufficient 

 

refrigerating capacity ,the resulting phenomena are its lower gas suction 

 

pressure and exhaust pressure as well as higher exhaust gas 

 

temperature. The exhaust tube feels rather hot ,and a continuous gas 

 

flowing sound louder than usual can be heard at the outlet of the 

 

capillary ,and no frost or a smaller quantity of loose frost appears on the 

 

evaporator .After shut down ,the balance pressure in the system is usually 

 

lower than the saturation pressure corresponding to the same ambient 

 

temperature . 

 

Remedy 

 

In case there is leakage of refrigerant from the system ,do not hurry to 

 

recharge it with refrigerant ,manage to find out leak points immediately ,and 

 

make a note of from where it leaks ---welding points and parts .After having 

 

them repaired ,recharge refrigerant . 

 

 

17 

 

Summary of Contents for HS-36I




























Reviews: