background image

• The clothes in the machine are

   too many.

• Clothes are not immediately taken

   out of the drum after the drying 

   process and left in the drum for

   a long period of time. 

•  Clothes are not properly sorted.

•  The temperature is setting is too high.

 

The cut out switch may operate for the following reasons:

1. Lint filter is clogged.

2. Exhaust outlets are blocked at the back of the dryer.

3. Poor ventilation in the laundry room (open a window or door)

4.  A piece of lightweight garment (e.g.: handkerchief) covers the filter.

Unit does

not start

• Power is cut.

• The power plug is not insered tightly

• Dry weight of clothes exceed 

   the rated capacity.

• The temperature fuse is cut.

• The filter is dirty.

• The air intake area or

   flexible duct is dirty.

• Take out some clothes, make sure the

   drum is not too full.

• Take out the clothes immediately when

  drying is finished.

• See page 7.

• Follow the fabric care label on the

  clothes.

• Follow the fabric care label on the clothes.

   Take out the clothes when it is still a little

   damp and then hang it until it becomes

    fully dry.

• Wait for electrical supply to resume.

• Check the power socket, make sure the

    plug is tightly secure in place.

• Dry weight must not exceed 6.5kg.

• Call for service.

• Clean the filter after each use.

• Clean the air intake or flexible duct.

• Too dry

• Use fabric softener. Turn the clothes

  inside-out to reduce friction. Spray starch

  solution on cuffs and necklines when

  ironing clothes.

• It is normal for synthetic fiber and

  permanent press fiber to form lumps.

External surfaces

are hot or there is

presence of burnt

smell

Clothes are

too dry

Clothes shrink

Fiber ball on

clothes

When in operation, the dryer can cause:

• Vibration noise: This occurs when the wet clothes turn and bump against

  one another.

• Bumping sound: When drying, steam is generated, comes out of the pipe

  and bumps against the bottom of the drum.

Safety reset

Precautions

Trouble  

 

Cause   

 

       Solution

10

11

These dryers have a safety cut out switch which is activated by temperature.

It will only be necessary to press the safety reset button if the dryer is not heating.

Allow the dryer at least 10 minutes to cool down before pressing the button. Press

the white button until you feel the reset switch click. The most common reason for 

the dryer to overheat is a clogged filter. Cleaning the filter after each load will 

avoid  repetitive operation of the safety cut out switch.

Summary of Contents for FP-91LFD070GMTM-N









Reviews: