I n s t a l l a t i o n a n d u s e r m a n u a l
V e r s i o n : 0 1 / 2 0 2 1
H
E
A
T
P
U
M
P
M
I
C
R
O
W
E
L
L
H
P
d.
Vacuumize completely before welding. Welding can only be carried out by
professional personnel in service center.
1
）
Attention
a.
Please read the following instructions before installation, use and
b.
Installation must be done by professional staff only in accordance with this manual.
c.
A leakage test must be performed after installation.
d.
If a repair is required, please contact the nearest after
strictly in accordance with manual. All repair practice by non
e.
Set proper temperature in order to get comfortable water temperature to avoid overheating or
overcooling.
f.
Please don’t stack substances, which will block air flow
efficiency of the heater will be reduced or even stopped.
g.
Don’t use or stock combustible gas or liquid such as thinners, paint and fuel to avoid fire.
h.
In order to optimize the heating effect, please install heat pre
swimming pool and the heater, and please use a recommended cover on the swimming pool.
i.
Connecting pipes of the swimming pool and the heater should be
2
）
Safety
a.
Please keep the main power supply switch far away from the children.
b.
When a power cut happens during operating, and later the power is restored, the heater will start up.
c.
Please switch off the main power supply in
damage that caused by lightning;
d.
Any repairing should be conducted in the area with good ventilation. The ignition source is prohibited
during the inspection.
e.
Safety inspection must be carried before the
order to minimize the risk.
f.
If R32 gas leaks during the installation process, all operations must be stopped immediately and call
the service center.
2.3
Handling precautions
Leave the condensing unit
Transport in lying position or turning the device over may harm the compressor resulting in unit’s
malfunction, failure or damage and will lead to loss of warranty.
The device must be handled with care and special attention avoiding any mechanical damage.
It is forbidden to apply any improper mechanical force onto the unit. This may cause mechanical
damage to the device.
It is forbidden to let the device fall freely onto the ground
impact.
Please notify your reseller or distributor if you suspect that the unit was delivered damaged. Unit
may seem to work well at start but small damage can make the unit go out
In such case the unit must be inspected and approved for further use by your reseller.
Please notify your reseller or distributor if directly after installation you suspect that unit is not
I n s t a l l a t i o n a n d u s e r m a n u a l
H P 1 7 0 0 / H P 2 1 0 0 /
Vacuumize completely before welding. Welding can only be carried out by
professional personnel in service center.
Please read the following instructions before installation, use and maintenance.
Installation must be done by professional staff only in accordance with this manual.
A leakage test must be performed after installation.
If a repair is required, please contact the nearest after-sales service center. The repair process must b
strictly in accordance with manual. All repair practice by non-professional is prohibited.
Set proper temperature in order to get comfortable water temperature to avoid overheating or
Please don’t stack substances, which will block air flow near inlet or outlet area, otherwise the
efficiency of the heater will be reduced or even stopped.
Don’t use or stock combustible gas or liquid such as thinners, paint and fuel to avoid fire.
In order to optimize the heating effect, please install heat preservation insulation on pipes between
swimming pool and the heater, and please use a recommended cover on the swimming pool.
Connecting pipes of the swimming pool and the heater should be ≤10m.
Please keep the main power supply switch far away from the children.
When a power cut happens during operating, and later the power is restored, the heater will start up.
Please switch off the main power supply in lightening and storm weather to prevent from machine
damage that caused by lightning;
Any repairing should be conducted in the area with good ventilation. The ignition source is prohibited
Safety inspection must be carried before the maintenance or repair for heat pumps with R32 gas in
If R32 gas leaks during the installation process, all operations must be stopped immediately and call
Handling precautions
Leave the condensing unit in vertical upright position for at least 2 hours before the installation.
Transport in lying position or turning the device over may harm the compressor resulting in unit’s
malfunction, failure or damage and will lead to loss of warranty.
be handled with care and special attention avoiding any mechanical damage.
It is forbidden to apply any improper mechanical force onto the unit. This may cause mechanical
It is forbidden to let the device fall freely onto the ground or any solid surface resulting in hard
Please notify your reseller or distributor if you suspect that the unit was delivered damaged. Unit
may seem to work well at start but small damage can make the unit go out-of
e the unit must be inspected and approved for further use by your reseller.
Please notify your reseller or distributor if directly after installation you suspect that unit is not
0 0 / 2 7 0 0 G r e e n
P a g e
8
/ 4 0
Vacuumize completely before welding. Welding can only be carried out by
Installation must be done by professional staff only in accordance with this manual.
sales service center. The repair process must be
professional is prohibited.
Set proper temperature in order to get comfortable water temperature to avoid overheating or
near inlet or outlet area, otherwise the
Don’t use or stock combustible gas or liquid such as thinners, paint and fuel to avoid fire.
servation insulation on pipes between
swimming pool and the heater, and please use a recommended cover on the swimming pool.
When a power cut happens during operating, and later the power is restored, the heater will start up.
lightening and storm weather to prevent from machine
Any repairing should be conducted in the area with good ventilation. The ignition source is prohibited
maintenance or repair for heat pumps with R32 gas in
If R32 gas leaks during the installation process, all operations must be stopped immediately and call
in vertical upright position for at least 2 hours before the installation.
Transport in lying position or turning the device over may harm the compressor resulting in unit’s
be handled with care and special attention avoiding any mechanical damage.
It is forbidden to apply any improper mechanical force onto the unit. This may cause mechanical
or any solid surface resulting in hard
Please notify your reseller or distributor if you suspect that the unit was delivered damaged. Unit
of-order in short time.
e the unit must be inspected and approved for further use by your reseller.
Please notify your reseller or distributor if directly after installation you suspect that unit is not
