Operation
The e-Trap voice command system remote comes set as an 8 channel remote.
To activate voice control refer to instructions.
NOTE:
The TP button allocation is defaulted to buttons 1 + 2
Using remote with voice mode on single shot mode
1.
Press the button you wish to activate and the ‘Voice’ LED will illuminate.
2.
When ready, call “PULL” with a firm voice. The ‘TX’ LED will flash and the
remote will exit voice mode.
3.
To exit voice mode at any time, press the
MENU
button firmly.
NOTE:
If no voice activation has been detected after 15 seconds, voice mode will
deactivate.
Using remote with voice continuous mode on
1.
Press the button you wish to activate and the ‘Voice’ LED will illuminate.
2.
Continue to hold until ‘DT’ LED illuminates.
3.
Now release button and after a 3 second delay. The ‘DT’ LED will turn off and
the ‘Voice’ LED will flash indicating continuous activation mode.
4.
When ready, call “PULL” with a firm voice. The ‘TX’ LED will flash, then the
‘DT’ LED will illuminate and stay on for the set dead time.
(Voice can’t activate again until dead time has elapsed. The default dead
time is 3 seconds).
5.
To exit at any time press
MENU
button firmly.
NOTE:
If no voice activation has been detected after 3 minutes, voice mode will
deactivate.
Using remote in auto mode with voice activation
1.
Ensure voice activation is on, then press and hold the
MENU
button.
2.
Press ‘Auto’ button (
4-D
) and the ‘Auto’ LED will illuminate.
3.
Release the
MENU
button and press a program number between 1 and 6.
The ‘Auto’ LED and ‘DT LED will be on solid for 3 seconds.
4.
After 3 seconds, the ‘DT’ LED will turn off and ‘Auto’ LED will flash. The system is
now ready.
5.
Call “PULL” to activate.
NOTE:
The ‘TX’ LED light will be on solid at the start of each program cycle and will
flash in between cycles.
Using remote in auto mode without voice activation
1.
Ensure voice activation is off, then press and hold the
MENU
button.
2
Press ‘Auto’ button (
4-D
) and the ‘Auto’ LED will illuminate.
3.
Release the
MENU
button and press a program number between 1 and 6.
The ‘Auto’ LED and ‘DT LED will be on solid for 3 seconds.
4.
After 3 seconds, the ‘DT’ LED will turn off and ‘Auto’ LED will flash. The system is now ready.
5.
Use the
TP
button to activate.
NOTE:
The ‘TX’ LED light will be on solid at the start of each program cycle and will flash in between cycles.
4
Microtech Designs
microtechdesigns.com.au
e-Trap 10 Button
Voice Command
Remote
TRANSCEIVER
1
Coding remote
1.
Press and hold
CODE
button until blue ‘Code’ LED comes on, then release
CODE
button.
2.
Press the button on the remote that you want to activate the Transceiver, the blue
‘Code’ LED will flash. Release button.
3.
Press remote button again and ‘Code’ LED will flash a second time to confirm.
Remote is now coded.
4.
You can follow up with a second remote, or if you press remote button for
a third time all LEDs will flash and code learn will be exited.
Code learn will exit after 5 seconds if no remotes are detected.
NOTE:
1.
This can only be done when voice activation is not enabled.
2.
If the Transceiver’s button allocation had been set to number 1,
even if you coded button 8 on remote, the Transceiver will only accept
button 1. Refer to
Clay Trap Transceiver
instructions to change.
10 bUTToN REmoTE
Microtech Designs
microtechdesigns.com.au
